少妇挑战三个黑人惨叫4p国语,久久亚洲精品无码VA大香大香,公交车大龟廷进我身体里

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

新聞資訊

如何通過雕刻機主軸電機聲音判斷故障

來源：http://editscore.net 時間：2021-06-18

主軸電機在工作時由于旋轉摩擦會發出一些聲音，正常工作的主軸聲音比較平和沒有多少雜音，如果發現主軸電機的聲音不正常就需要對主軸進行檢修了。

When the spindle motor is working, it will make some noise due to the rotating friction. The sound of the normal working spindle is relatively flat and there is not much noise. If the sound of the spindle motor is abnormal, it is necessary to overhaul the spindle.

由于五軸保麗龍雕刻機主軸電機長時間高頻率的運轉，再者使用不當,主軸很容易出現一些噪音，但是一般的使用客戶們很難通過聲音來判斷主軸電機的具體問題。今天濟南凸凹機械在這給大家分析下，主軸電機的聲音不正常有哪些情況，希望大家可以對自己的主軸進行及時的保養。

Due to the engraving machine spindle motor long time high frequency operation, and improper use, the spindle is prone to some noise, but the general use of customers are difficult to judge the specific problems of the spindle motor through the sound. Today, Jinan convex concave machinery in this analysis for you, the sound of the spindle motor is abnormal, what are the circumstances, I hope you can timely maintenance of their own spindle.

1、噠噠的聲音：聲音頻率隨軸承轉速而變化，零件表面波紋度是引起噪音的主要原因。解決方法：改善軸承滾道表面加工質量，降低波紋度幅值、減少碰傷、修正游隙預緊力和配合，檢查自由端軸承的運轉，改善軸與軸承座的精度安裝方法。

1. Dada sound: the sound frequency changes with the bearing speed, and the surface waviness of parts is the main cause of noise. Solutions: improve the surface processing quality of the bearing raceway, reduce the amplitude of waviness, reduce the impact, correct the clearance preload and fit, check the operation of the free end bearing, and improve the precision installation method of the shaft and bearing seat.

2、嗡嗡的聲音：馬達無負荷運轉是發出類似蜂鳴一樣的聲音，且馬達發生軸向異常振動,開或關機時有嗡嗡聲。解決方法：多出現在潤滑狀態不好,以及在冬天且兩端用球軸承的馬達，主要是軸調心性能不好時，軸向振動影響下產生的一種不穩定的振動.

2. Buzzing sound: when the motor runs without load, it makes a sound similar to a beep, and the motor has abnormal axial vibration, and there is a buzzing sound when it is turned on or off. Solution: it often occurs in the motor with poor lubrication and ball bearings at both ends in winter, which is mainly a kind of unstable vibration under the influence of axial vibration when the shaft alignment performance is not good

3、雜質音：由軸承或的清潔度引起,發出一種不規則的異常音，聲音時有時無,時大時小,在高速電機上發生頻繁。解決方法：選用好的油脂、提高注脂前的清潔度、加強軸承的密封性能、提高安裝環境的清潔度

3. Impurity sound: it is caused by the bearing or high-quality cleanliness, and makes a kind of irregular abnormal sound. The sound is sometimes non-existent, sometimes large and sometimes small, which occurs frequently in high-speed motors. Solutions: select good grease, improve the cleanliness before grease injection, strengthen the sealing performance of bearing, and improve the cleanliness of installation environment

4、淅瀝淅瀝的聲音：由保持器與滾動體振動、沖撞產生,不管潤滑脂種類如何都可能產生，承受力矩、負荷或徑向游隙大的時候更容易產生.解決方法:提高保持器精度、選用游隙小的軸承或?qū)S承施加預負荷、降低力矩負荷，減少安裝誤差、選用好的油脂。

4. Rustling sound: it is produced by the vibration and collision between retainer and rolling element, no matter what kind of grease is, and it is easier to produce when bearing torque, load or radial clearance is large. Solutions: improve the accuracy of retainer, select bearing with small clearance or preload bearing, reduce torque load, reduce installation error and select good grease.