《[国产剧情]国产av-愿望成真》,被几个男人用按摩器折磨,av无码国产精品色午夜

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

新聞資訊

數控開料機如何合理保養提高家具生產效率

來源：http://editscore.net 時間：2022-01-14

1、開機前，先檢查設備的線路是否完好，電壓是否穩定，確認無誤后才能開機，待機空置一段時間后再開始加工。

1. Before starting up, check whether the circuit of the equipment is intact and whether the voltage is stable. Start up after confirming that there is no error. Wait for a period of time and then start processing.

2、數控開料機主軸有兩種類型，一種是風冷主軸，另一種是水冷主軸，冷卻軸需要清洗和冷卻才能正常工作，在此提醒大家：水冷主軸不能缺水。

2. There are two types of spindles of CNC cutting machine, one is air-cooled spindle and the other is water-cooled spindle. The cooling shaft needs cleaning and cooling to work normally. Here we remind you that the water-cooled spindle cannot be short of water.

3、除了以上保養工作外，還要注意水溫，冷卻水溫度過高會使冷卻效果大大下降，對主軸造成一定的損壞，因此需要及時更換冷卻水。冬天還要采取防凍措施，防止凍裂水管。

3. In addition to the above maintenance work, pay attention to the water temperature. Too high cooling water temperature will greatly reduce the cooling effect and cause certain damage to the main shaft. Therefore, the cooling water needs to be replaced in time. Antifreeze measures should also be taken in winter to prevent frost cracking of water pipes.

對數控開料機電路箱的散熱性和通風系統進行定時清掃，檢查各風扇是否工作正常，對電氣控制箱內灰塵進行定時清掃，檢查接線端子螺釘松動，確保電路使用可靠。

Regularly clean the heat dissipation and ventilation system of the circuit box of the NC opener, check whether each fan works normally, regularly clean the dust in the electrical control box, and check the looseness of the connecting terminal screws to ensure the reliable use of the circuit.

及時清理導軌及周?chē)哪拘迹皶r(shí)給設備的驅動系統加料。

Clean the wood chips on the guide rail and around in time, and feed the driving system of the equipment in time.

6、將感應器上的灰塵、油污及時除干凈。

6. Remove the dust and oil stain on the sensor in time.

7、在數控開料機上開料后，取出刀片，使主軸夾頭處于放松狀態。有利于延長主軸座的使用壽命。

7. After cutting on the NC cutting machine, take out the blade to make the spindle chuck in a relaxed state. It is beneficial to prolong the service life of the spindle seat.

下一步我們開始清理臺面，可用毛刷清理桌面，注意一般臺面盡量不要雜物堆積，以免臺面變形。割斷電源前，應將機頭移到左下或右下位置，避免碰撞。

Next, we start to clean the table. We can clean the table with a brush. Note that the general table should not accumulate sundries as far as possible to avoid deformation of the table. Before cutting off the power supply, move the machine head to the lower left or right position to avoid collision.

8、長時間不使用數控開料機時，盡量每周通電一次，防止機器受潮，保證設備的電氣元件性能穩定可靠。

8. When the numerical control cutting machine is not used for a long time, try to power on once a week to prevent the machine from moisture and ensure the stable and reliable performance of the electrical components of the equipment.

9、數控開料機如經常打開櫥柜，通常在打開櫥柜時空氣中會有灰塵、木屑或金屬粉塵，一旦掉進電控箱的電路板或電子設備上，就容易造成元件之間的絕緣電阻降低，甚損壞元件及電路板。

9. If the NC cutting machine often opens the cabinet, there will be dust, sawdust or metal dust in the air when opening the cabinet. Once it falls into the circuit board or electronic equipment of the electric control box, it is easy to reduce the insulation resistance between components and even damage components and circuit boards.

本文的精彩內容由四工序開料機為您提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入：http://editscore.net/我們有專門的客服為您解答問題

The wonderful content of this article is provided by the four process cutting machine. There are many wonderful content on this website. You can click to enter more content: http://editscore.net/ We have special customer service to answer your questions