聯系我們
18560023440
王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間
新聞資訊
雕刻機經常斷刀怎么辦?
來源：http://editscore.net 時間：2022-02-14
如今越來越多的人開始使用雕刻機，很多人總是會出現雕刻機斷刀的情況，很多人都不知道這是怎么回事，今天我們就來告訴大家答案！
Nowadays, more and more people begin to use engraving machines. Many people always break the knife of engraving machines. Many people don't know what's going on. Today we'll tell you the answer!
雕刻機經常遇到斷刀的情況，其實這并不一定是石雕所存在的問題，建議對不同情況下，有一個相應的解決方案會更好。導致斷刀發生的原因有好幾種，主要是下面幾種問題引起，可以盡量避免或者采取相應的措施來解決。
Engraving machines often encounter knife breakage. In fact, this is not necessarily the problem of stone carving. It is suggested that it would be better to have a corresponding solution for different situations. There are several reasons for tool breakage, mainly caused by the following problems, which can be avoided or solved by taking corresponding measures.
1.雕刻機本身的問題。在雕刻機進行操作時，若雕刻機安裝不正確，或卡頭內有雜物，將導致工具不垂直，將造成斷刀，所以安裝工具時要仔細檢查雕刻機安裝是否正確。
1. Problems of engraving machine itself. During the operation of the engraving machine, if the engraving machine is installed incorrectly or there are sundries in the chuck, the tool will not be vertical and the knife will be broken. Therefore, carefully check whether the engraving machine is installed correctly when installing the tool.
2.根據加工物料選擇相應的刀具。這個道理很容易理解，比如說木材與翡翠的硬度差太大，木工刀是無法用來雕刻翡翠的，而像水晶、綠松石、軟玉、硬玉等，很多材料的硬度是有差別的，所以要選擇合適材料的刀具進行加工。
2. Select the corresponding tool according to the processing materials. This reason is easy to understand. For example, the hardness difference between wood and jadeite is too large, and woodworking knives cannot be used to carve jadeite. For example, the hardness of many materials, such as crystal, turquoise, nephrite, jadeite, etc., is different, so it is necessary to select appropriate knives for processing.
3.加工速度太快。對每一種材料的硬度不同，而且刀具的耐受性一定也有一定的限制，如果加工速度過快也會造成斷刀現象，因此在加工過程中要根據實際情況調整速度，避免過快。
3. The processing speed is too fast. The hardness of each material is different, and the tolerance of the tool must be limited. If the processing speed is too fast, it will also cause tool breakage. Therefore, the speed should be adjusted according to the actual situation in the processing process to avoid too fast.
4.刀道間隙太大，下刀速度太快。同樣地，對加工速度的理解是，加工時刀距過大或刀片速度過快，都有可能超出刀具承受范圍而造成斷刀。
4. The clearance of knife path is too large and the cutting speed is too fast. Similarly, the understanding of machining speed is that if the tool distance is too large or the blade speed is too fast, it may exceed the bearing range of the tool and cause tool breakage.
5.高度差異過大。同一種刀具路徑的高低差過大，如超過刀具的承受力范圍，都會引起斷刀情況。
5. The height difference is too large. If the height difference of the same tool path is too large, if it exceeds the bearing range of the tool, it will cause tool breakage.
以上就是雕刻機會出現斷刀的幾個原因，希望大家在使用設備時一定要注意哦！
The above are the reasons for the broken knife in the carving opportunity. I hope you must pay attention to it when using the equipment!
本文由五軸保麗龍雕刻機為您提供，我們的網站是：http://editscore.net/我們將以全心全意的熱情為您提供服務，歡迎您的訪問
This article is provided by the five axis poly dragon engraving machine. Our website is: http://editscore.net/ We will provide you with services with wholehearted enthusiasm. Welcome to visit
木工雕刻機
1325木工雕刻機獨...
1325木工雕刻機
1325木工鏤空花格...
1225型平雕圓雕一...
相關產品：
