一、，在Z軸定位的時候，不是讓刀碰到材料面，而是移開材料讓刀直接碰到臺面，碰到就可以了，不要深了，在這個地方Z軸先歸零，然后根據你在文泰里設置的切割深 度在提高相應的高度，比如你在文泰設置切割深 度為10，那么在這里我們精 確的讓刀提高10，在這再讓Z軸歸零，這個就是Z軸的原 點了。 根據文泰里的設置深 度，機器下的低點就是我門歸零的地方，正好是在臺面的上面，這樣保證了材料完全刻透而不會刻到臺面。

1、 First of all, when positioning the z-axis, instead of letting the knife touch the material surface, move the material and let the knife touch the table directly. Don't touch it too deep. In this place, the z-axis will return to zero first, and then increase the corresponding height according to the cutting depth you set in Wentai. For example, if you set the cutting depth in Wentai as 10, then we will do fine here Let the knife increase by 10, and then let the z-axis return to zero. This is the origin of the z-axis. According to the setting depth of wentaili, the low point under the machine is the place where our door returns to zero, which is just on the top of the table, so as to ensure that the material is completely engraved without being engraved on the table.

二、在文泰里的切割深 度設置為0，然后在存路徑的時候高點設置抬刀距離就行了。

2、 Set the cutting depth of wentaili to 0, and then set the tool lifting distance at the high point when saving the path.

三、還可以使用微動開關進行上下限位，每軸2個限位開關，做硬件限位心理有個底 這樣無論怎樣都不會撞臺面了?；蛘呤褂脤?duì)射光槽，但如果沒有擋屑裝置，對射很可能因碎屑的進入而頻繁出麻煩。

3、 You can also use the micro switch for the upper and lower limit, 2 limit switches for each axis, so that there is a bottom for the hardware limit psychology, so that no matter how it will not hit the table. Or use the opposite light groove, but if there is no chip blocking device, the opposite light may be in trouble frequently due to the entry of debris.

5、保存精雕路徑

5. Save the carving path

選中做好的路徑——點擊【保存精雕路徑】——點擊【查找】找到要保存的位置，文件類型選擇(*.nc)命名后點擊【保存】——抬到距離一般設置5-10——點擊【確認】

Select the path you want to save - click save path - click find to find the location you want to save. Select the file type and name it. Click Save - move to the general distance setting of 5-10 - click OK

以上就是石材雕刻機廠家給大家分享的雕刻機操作技巧 木工雕刻機如何操作不傷臺面的詳細解答，不知道大家對小編的介紹是否滿意。如果您還想了解更多相關 方面的精彩內容，還請您繼續關注我們的版塊!

The above is the stone carving machine manufacturers to share the carving machine operation skills, wood carving machine how to operate without damaging the table, I do not know if you are satisfied with the introduction of Xiaobian. If you want to know more about the wonderful content, please continue to pay attention to our section!