How to choose the power of motorized spindle of NC engraving machine? Is the higher the power, the better? Of course not.

數控雕刻機的主軸電機的功率要根據所雕刻的對象進行選擇，下面我們介紹一下：

The power of spindle motor of NC engraving machine shall be selected according to the engraving object. Let's introduce it below:

根據客戶加工的材料、質量效果來進行選擇主軸的功率大小，浮雕、鏤空、切割、刻字等加工效果選擇的主功率是不一樣的，有的加工材料本身的硬度不同也會選擇不同功率！大部分都會選擇能夠滿足需求后偏大一點比較好。電機的實際消耗功率與負載有關，同樣的負載下，大小功率的主軸實際耗電相差不大。但是由于轉動體重量、軸承尺寸等，一般而滿足需求后偏大一點比較好。對于雕刻機主軸來說，同樣的負載下，大小功率的的主軸實際耗電相差不大。

Choose the power of the spindle according to the materials and quality effects processed by customers. The main power selected for the processing effects such as relief, hollowing out, cutting and lettering is different. Some processing materials will choose different power due to their different hardness! Most of them will choose to be a little bigger after meeting the demand. The actual power consumption of the motor is related to the load. Under the same load, the actual power consumption of the spindle with large and small power is almost the same. However, due to the weight of the rotating body and the size of the bearing, it is generally better to be a little larger after meeting the demand. For the engraving machine spindle, under the same load, the actual power consumption of the spindle with large and small power is almost the same.

普通的選擇如下：

Common choices are as follows:

廣告雕刻機：雕刻對象為比較軟的材質所以廣告雕刻機的主軸功率在1.5kw—3.0kw以內就可以，這樣選擇的話既可以達到雕刻目的還能節省成本。

Advertising engraving machine: the engraving object is a relatively soft material, so the main shaft power of the advertising engraving machine can be within 1.5kw-3.0kw. In this way, the engraving purpose can be achieved and the cost can be saved.

木工雕刻機：木工雕刻機的主軸電機可根據所加工木料的硬度進行選擇其功率：一般在2.2kw—4.5kw左右，這也是普通選擇。

Woodworking engraving machine: the spindle motor of woodworking engraving machine can be selected according to the hardness of the processed wood. Its power is generally about 2.2kw-4.5kw, which is also a common choice.

石材雕刻機：廠家用石材雕刻機的主軸功率相對要高一些，一般在4.5kw—7.5kw左右，更常用的還是5.5kw主軸電機

Stone carving machine: the spindle power of the stone carving machine used by the manufacturer is relatively higher, generally about 4.5kw-7.5kw, and the most commonly used is the 5.5kW spindle motor

墓碑雕刻機：墓碑雕刻機的主軸功率也要根據所加工的石料硬度進行選擇，一般功率在3.0kw—4.5kw即能滿足客戶需求

Tombstone engraving machine: the spindle power of the tombstone engraving machine should also be selected according to the hardness of the processed stone. Generally, the power is 3.0kw-4.5kw, which can meet the needs of customers

玉石雕刻機：玉石雕刻機由于其床身較小主軸電機的功率一般在2.2kw-3.0kw即可。

Jade carving machine: due to its small bed, the power of main shaft motor of jade carving machine is generally 2.2kw-3.0kw.

主軸電機功率太大不僅浪費電能還會增加客戶的購機成本，功率太小的話又不能其雕刻功率需求，所以選擇適合自己的主軸電機的功率對客戶來說是相當重要的!

If the power of spindle motor is too large, it will not only waste electric energy, but also increase the purchase cost of customers. If the power is too small, it can not meet the engraving power demand. Therefore, it is very important for customers to choose the power of spindle motor suitable for themselves!

以上就是今天小編給大家提供的精彩內容，更多的精彩內容請點擊進入我們的網站：石材雕刻機 http://editscore.net/

The above is the wonderful content provided by Xiaobian today. For more wonderful content, please click to enter our official website: stone carving machine http://editscore.net/