久久久国产成人一区二区,久草在在线免在线观看视频

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

業內資訊

保麗龍雕刻機主軸噪音大怎么辦？

來源：http://editscore.net 時間：2021-12-06

下面就一起來看看開料機主軸噪音大原因及解決方法，希望對大家有所幫助

Let's take a look at the causes and solutions of high noise of the main shaft of the cutting machine, hoping to help you

主軸在工作時有噪音，有時沒有，聲音大小還不定，這個主要是數控開料機或木工雕刻機的零件外表的波紋度導致的，需要改進軸承滾道外表加工質量，改進軸與軸承座的精度裝置辦法。那么，在現實操作中，面對主軸發出的一些噪音，主要有以下四種：

When the spindle is working, there is noise, sometimes there is no noise, and the sound size is uncertain. This is mainly caused by the waviness of the part surface of the NC cutting machine or woodworking engraving machine. It is necessary to improve the processing quality of the bearing raceway surface and the accuracy of the shaft and bearing seat. Then, in real operation, there are mainly four kinds of noise emitted by the spindle:

一、淅瀝淅瀝的聲音：由保持器與滾動體振動、沖撞產生，不管潤滑脂種類如何都可能產生，承受力矩、負荷或徑向游隙大的時候更容易產生

1、 Intermittent sound: it is generated by the vibration and collision between the retainer and the rolling element. It may occur regardless of the type of grease. It is more likely to occur when the bearing torque, load or radial clearance is large

解決方法：保持器精度、選用游隙小的軸承或對軸承施加預負荷、降低力矩負荷，減少安裝誤差、選用好的油脂

Solution: keep the accuracy of the retainer, select the bearing with small clearance or apply preload to the bearing, reduce the torque load, reduce the installation error, and select good grease

二、雜質音：由軸承或好的清潔度引起，發出一種不規則的異常音，聲音時有時無，時大時小，在電機上發生頻繁

2、 Impurity sound: it is caused by the bearing or good cleanliness. It emits an irregular abnormal sound, sometimes no, sometimes large and sometimes small, which occurs frequently on the motor

解決方法：選用好的油脂、注脂前的清潔度、加強軸承的密封性能、安裝環境的清潔度

Solution: select good grease, the cleanliness before grease injection, strengthen the sealing performance of the bearing and the cleanliness of the installation environment

三、嗡嗡的聲音：馬達無負荷運轉發出類似蜂鳴一樣的聲音，且馬達發生軸向異常振動，開或關機時有嗡嗡聲

3、 Buzzing sound: when the motor runs without load, it makes a sound similar to buzzing, and the motor has abnormal axial vibration. There is buzzing sound when it is turned on or off

解決方法：多出現在潤滑狀態不好，以及在冬天且兩端用球軸承的馬達，主要是軸調心性能不好時，軸向振動影響下產生的一種不穩定的振動

Solution: most motors with poor lubrication and ball bearings at both ends in winter are unstable vibration under the influence of axial vibration when the shaft centering performance is poor

四、噠噠的聲音：聲音頻率隨軸承轉速而變化，零件表面波紋度是引起噪音的主要原因

4、 Clatter sound: the sound frequency changes with the bearing speed, and the surface waviness of parts is the main cause of noise

解決方法：改良軸承滾道表面加工質量，降低波紋度幅值、減少碰傷、修正游隙預緊力和配合，檢查自由端軸承的運轉，改良軸與軸承座的精度安裝方法

Solution: improve the surface processing quality of bearing raceway, reduce the amplitude of waviness, reduce bumps, correct the preload and fit of clearance, check the operation of free end bearing, and improve the precision installation method of shaft and bearing seat

數控開料機加工時，主軸是重要組成部分，作用大，很容易出問題，有時會產生很大的噪音。如果在工作中產生嗡嗡的蜂鳴聲，那就是主軸出現了問題，不能完成在負荷狀態下的工作，建議是更換主軸或進行維修。

In NC cutting machine processing, the spindle is an important part and plays a great role. It is easy to have problems and sometimes produce a lot of noise. If there is a buzzing sound during work, it means that the spindle has a problem and cannot complete the work under load. It is recommended to replace the spindle or carry out maintenance.

以上就是保麗龍雕刻機http://editscore.net/為大家介紹的內容，感謝您在百忙之中查看我公司的信息內容，如果您想要了解的更多，歡迎您來電進行咨詢!

The above is the poly Dragon carving machine http://editscore.net/ Thank you for checking the information of our company in your busy schedule. If you want to know more, you are welcome to call for consultation!

相關產品：