Generally, the price of engraving machine depends on the configuration of engraving machine and the size of machine tool. But still need from the following aspects to choose their own engraving machine.

驅動動系統：目前雕刻機驅動系統主要分步進系統和系統兩大類，步進系統占著主導地位這要原因經濟實惠能滿足一般客戶的使用要求，步進系統屬于半閉環系統精度以步距角計算，系統完全屬于封閉環模式內有測量反饋系統所以精度比較高，動力大、運行平穩、要求較高的客戶可選擇驅動系統的機器（稍貴）。

Driving system: at present, the driving system of engraving machine is mainly divided into two categories: step-by-step system and system, and the stepping system is dominant. This is because it is economical and can meet the requirements of general customers. The stepping system belongs to a semi closed-loop system, and its accuracy is calculated by the step angle. The system is completely in the closed-loop mode, and there is a measurement feedback system, so the precision is relatively high, the power is large, and the operation is stable Customers with higher requirements can choose to drive the machine (the price is slightly higher).

目前市場上也出現了半系統，是改進版的步進系統，請客戶選機器時注意。(分國產和進口)控制系統：目前以維宏、DSP操作系統、mach3為主導少部分，進口臺灣寶元和新代控制系統。作圖軟件：一般使用、文泰、精雕、TYPE3、artcam。

At present, there is a Semi-system in the market, which is an improved version of the step-by-step system. Please pay attention when selecting the machine. (domestic and imported) control system: at present, Weihong, DSP operating system and Mach3 are the leading parts, while Taiwan Baoyuan and new generation control system are imported. Drawing software: general use, Wentai, Jingdiao, type3, ArtCAM.

雕刻機傳動方式：目前雕刻機分三種傳動方式，絲杠傳動、齒條傳動和同步帶傳動。

Engraving machine transmission mode: at present, engraving machine is divided into three transmission modes, screw drive, rack drive and synchronous belt drive.

絲杠機優缺點：絲杠傳動是雕刻機起源時的傳動方式，特點精度高，運行速度慢，環境要求較高，使用壽命相對較短，Y軸單絲杠不易太長（機型不能太大），高速運行時容易抖動，如果安裝精度不高Y軸絲杠長時間運行將有被甩斷的可能。

Advantages and disadvantages of lead screw machine: screw drive is the transmission mode of engraving machine origin, with high precision, slow running speed, high environmental requirements, relatively short service life, Y-axis horizontal screw is not easy to be too long (the model can not be too large), and it is easy to shake when running at high speed. If the installation accuracy is not high, the y-axis lead screw may be broken if it runs for a long time.

如果要求精度過高的可以Ｙ軸雙絲杠結構來滿足要求，一般加工速度７米左右。（主要適用廣告、木制品、小工藝品、較輕石材根據刀具不同可加工任意雕刻材料）

If the required accuracy is too high, Y-axis double lead screw structure can meet the requirements, and the general processing speed is about 7 meters. (mainly suitable for advertising, wood products, small handicrafts and light stone. It can process any carving material according to different cutting tools)

齒條機優缺點：齒條機是既絲杠機的升級版，介于絲杠機無法滿足高速度加工的要求而新開發的機型，速度快、環境要求不苛刻相對使用壽命長、精度相對絲杠機低一些，齒條機Ｙ軸Ｘ軸為齒輪齒條傳動、Ｚ軸一般為絲杠傳動，精度要求主要根據導軌和齒輪齒條的嚙合精度來決定。機器尺寸長度可以夠大，維護方便一般配備手動注油系統，建議加工速度可達15米左右。

Advantages and disadvantages of rack machine: rack machine is an upgraded version of lead screw machine, which can not meet the requirements of high-speed processing. However, the newly developed machine has the advantages of fast speed, low environmental requirements, long service life and low precision compared with the lead screw machine. The Y-axis and x-axis of the rack machine are driven by the rack and pinion, and the z-axis is generally driven by the lead screw. The accuracy requirements are mainly based on the guide rail and gear rack Meshing accuracy. The size and length of the machine can be large enough and easy to maintain. Generally, it is equipped with manual oiling system, and the processing speed is recommended to be about 15m.

同步帶傳動：同步帶傳動主要用于激光雕刻機及等離子切割，質量輕、精度高、好維護、時間久容易松弛影響加工精度等特點。（激光機主要使用于廣告業、工藝品雕刻、布匹，皮革、玻璃、石材、水晶等一些非金屬材料的影雕線雕等也可在少數金屬材料上加工、區間和激光管的功率有關

Synchronous belt drive: synchronous belt drive is mainly used for laser engraving machine and plasma cutting. It has the characteristics of light weight, high precision, good maintenance, long time and easy relaxation, which affects the processing accuracy. (laser machines are mainly used in advertising, arts and crafts carving, cloth, leather, glass, stone, crystal and other non-metallic materials for shadow carving, line carving, etc., and can also be processed on a few metal materials. The price range is related to the power of the laser tube
關鍵詞：保麗龍雕刻機